Project Description

Lead time 20–30 days
Bright annealed available
Quote within 24 hours
Cut length from 300 mm
DIN 2391 is the German precision tube standard that half the world’s hydraulic drawings still reference, even though it was withdrawn and replaced by EN 10305-1 more than twenty years ago. The grades — St35, St45, St52 — correspond to E235, E235 and E355 in the current standard, and the condition codes BK, BKW, BKS, GBK and NBK correspond to +C, +LC, +SR, +A and +N. Nothing about the tube has changed; only the label. This page is written for the buyer who has an old drawing in front of them: what each designation means, what tolerance class to expect, and what to order today so the certificate matches the drawing without a substitution debate.
The old designations against the current ones
Table 1 — DIN 2391 to EN 10305-1
| DIN 2391 grade | EN 10305-1 grade | Steel number | Tensile, normalized | Yield, normalized |
|---|---|---|---|---|
| St35 | E235 | 1.0308 | 340 – 480 MPa | 235 MPa |
| St45 | E235 (higher carbon end) or E275 where specified | 1.0308 | 340 – 480 MPa | 235 MPa |
| St52 | E355 | 1.0580 | 490 – 630 MPa | 355 MPa |
St45 has no exact successor — the EN series jumped from E235 to E355, so old St45 drawings are usually satisfied by E235 with a note, or by E355 where the strength was genuinely needed. Check which one the design assumed before substituting.
Table 2 — Condition codes
| DIN 2391 | EN 10305-1 | Last operation | Effect on the part |
|---|---|---|---|
| BK | +C | Final cold draw, no heat treatment | Hardest and strongest; will move when machined |
| BKW | +LC | Heat treat then light finishing draw | Some forming capacity retained |
| BKS | +SR | Stress relief after the final draw | Stable when machined on one side |
| GBK | +A | Annealed in controlled atmosphere | Soft, free machining |
| NBK | +N | Normalized in controlled atmosphere | Uniform structure, predictable hardening |
Tolerance classes
Table 3 — Outside diameter tolerance to ISO 286 (all minus, zero above nominal)
| Nominal OD | h9 | h10 | h11 | Typical order |
|---|---|---|---|---|
| 10 – 18 mm | 0 / −43 µm | 0 / −70 µm | 0 / −110 µm | h11 for general machining stock |
| Over 18 – 30 mm | 0 / −52 µm | 0 / −84 µm | 0 / −130 µm | h9 for bearing seats |
| Over 30 – 50 mm | 0 / −62 µm | 0 / −100 µm | 0 / −160 µm | h10, the hydraulic default |
| Over 50 – 80 mm | 0 / −74 µm | 0 / −120 µm | 0 / −190 µm | h9 only by agreement above 60 mm |
| Over 80 – 120 mm | 0 / −87 µm | 0 / −140 µm | 0 / −220 µm | h11 for barrel stock before honing |
The tolerance class is chosen at order and it drives the price: h11 is a normal drawing pass, h9 needs a sizing pass and a straighter tube. Specifying h9 “to be safe” on a part that only needs h11 is a straight cost increase with no benefit.
Other tolerances
Table 4 — Commercial values we hold
| Parameter | Standard | Tighter by agreement |
|---|---|---|
| Wall thickness | ±10% of nominal | ±7.5% |
| Inside diameter | H10 where drawn over a mandrel | H9 or H8 |
| Straightness | 0.5 mm per metre | 0.3 mm/m after stress relief |
| Ovality | Within the OD band | Half the OD tolerance |
| Length | Cut length +20/−0 mm | ±2 mm on short lengths |
| Surface, bright annealed | Ra 0.8 – 1.6 µm | Ra 0.4 µm after skiving or honing |
Where DIN 2391 tube goes
Hydraulic cylinder barrels
St52 / E355 in BKS (+SR), bored and honed after delivery. The stress relief is what keeps the bore round.
Pneumatic cylinders
St35 / E235 with a tight ID and Ra 0.8 µm after skiving, where pressure is low and finish drives the seal life.
Automotive components
Shock absorber bodies, steering columns and axle tubes, often in BKW (+LC) because they are formed after delivery.
Machine building
Shaft sleeves, bushes and rollers turned from GBK (+A) stock, where the drawn bore saves a boring operation.
Bearing spacers
BK (+C) with an h9 OD, cut to width and used without further machining.
Furniture and frames
St35 in NBK (+N) for bending and welding, where formability matters more than strength.
Frequently asked questions
Is DIN 2391 still valid?
It was withdrawn and replaced by EN 10305-1. Drawings that cite it are still common and the tube is still made to those dimensions, but a certificate issued today will reference EN 10305-1 unless you specifically ask for the old designation.
What is St35 in the current standard?
E235, steel number 1.0308. St52 is E355, 1.0580. St45 sits awkwardly between them and is normally resolved at quotation stage.
What does BKS mean?
Cold drawn and stress relieved, the equivalent of +SR. It is the condition to specify for a cylinder barrel that will be machined on one side, because it prevents the tube bending as metal is removed.
Which tolerance class should I specify?
Only as tight as the part needs. h11 for general machining stock, h10 for a hydraulic barrel, h9 for a bearing seat or a bore that will not be touched. Every step tighter costs money at the drawing stage.
Can you supply the ID tolerance as well as the OD?
Yes where the tube is drawn over a mandrel. State ID and OD, or ID and wall — not all three, because the drawing pass fixes two and the third follows.
What is the difference between this and DIN 2391-2?
Part 1 covered the dimensions and tolerances, part 2 the specific requirements per grade. Both were replaced by the single EN 10305-1, which now carries dimensions, tolerances, grades and conditions together.
Is bright annealed available?
Yes — GBK (+A) and NBK (+N) are annealed in a controlled atmosphere and arrive bright. Pickled stock is cheaper and has a matt grey surface.
What is the minimum order and lead time?
500 kg per size. Lead time is 20–30 days; h9 tolerance on large diameter and bright annealed material run towards the longer end.
Request a quote
Related products
Cold Drawn Seamless TubeThe product page, sizes and process
1026 Cold Drawn TubingASTM A519 grade
Chrome Plated TubePiston rod finished from a +SR base tube
Hot Rolled Mechanical TubeThick wall stock, H11 bore
E470 20MnV6 Hollow BarHigher strength thick wall alternative
All cold drawn tube — CDS, honed, skived and plated · Guide: cold drawn seamless tube, tolerance classes and delivery conditions
Request a quotation
Tell us OD, ID or wall, tolerance class, condition and quantity. We reply within 24 hours with price, lead time and the EN equivalent of your DIN designation.