Project Description

ASTM A270 sanitary stainless steel tube, 180 grit polished bore, for dairy and food process lines
1/2" – 12"outside diameter
0.049" – 0.15"wall thickness
Ra ≤ 0.8 µmpolished bore
304 / 316Lgrades stocked
3-A · FDAhygienic compliance
12.5%wall tolerance
MOQ 300 kg per size
Lead time 25–30 days
Finish 180 / 240 grit, EP on request
Quote within 24 hours
Borescope report on request
Building a hygienic line? Send OD, wall, grade and finish (grit or Ra) — quotation back within 24 hours.
Get a quote

ASTM A270 is the sanitary specification: austenitic stainless tube for dairy and food service where the surface finish is a hygiene requirement rather than a cosmetic one. What separates it from ordinary stainless tube is the bore. Any pit, scratch or weld bead in a product contact surface holds residue, and residue grows bacteria no matter how good the CIP cycle is — so A270 tube is supplied with a controlled internal finish, usually 180 grit mechanical polish at Ra 0.8 µm or better, and it is dimensionally consistent enough that a hygienic fitting will butt up square. We supply 1/2 to 12 inch outside diameter, 0.049 to 0.15 inch wall, in 304, 304L, 316 and 316L, in annealed and pickled, polished or bright annealed condition, with a 12.5% wall tolerance and a borescope report on request.

Grades and mechanical properties

Table 1 — A270 grades

Grade C max Cr Ni Mo Tensile min Yield min Elongation
TP304 0.08 18.0 – 20.0 8.0 – 11.0 — 515 MPa 205 MPa 35%
TP304L 0.035 18.0 – 20.0 8.0 – 12.0 — 485 MPa 170 MPa 35%
TP316 0.08 16.0 – 18.0 10.0 – 14.0 2.00 – 3.00 515 MPa 205 MPa 35%
TP316L 0.035 16.0 – 18.0 10.0 – 14.0 2.00 – 3.00 485 MPa 170 MPa 35%

316L is the default for anything with a CIP cycle. The molybdenum resists the chloride in cleaning chemicals, and the low carbon stops sensitisation in the weld heat-affected zone — which in a hygienic line is a corrosion site you cannot inspect from outside.

Size range and tolerance

Table 2 — What A270 covers

Parameter Range Note
Outside diameter 1/2" – 12" (12.7 – 304.8 mm) 12 inch is the specification ceiling; above that it is fabricated
Common dairy sizes 1/2" – 2-1/2" Where most hygienic fittings and valves sit
Wall thickness 0.049" – 0.15" (1.24 – 3.81 mm) Thin wall for clamp fittings, heavy wall for welded lines
Wall tolerance 12.5% of nominal The specification figure — not tighter
OD tolerance Per A270 table by size Tight enough for a hygienic clamp ferrule to seat
Length Random 6 m, or cut to length Cut ends square and deburred; burrs are a hygiene defect
Units Inch-pound The specification is written in inch-pound; metric equivalents are nominal

Surface finish — the part that actually matters

Table 3 — Finish options and what they are for

Finish Typical Ra Where it is accepted Limitation
Mill finish, annealed and pickled Ra 2.0 – 3.0 µm Non-product-contact utility lines only Not acceptable for a product contact surface
Mechanical polish, 180 grit Ra 0.8 µm or better The general dairy and food standard Polish direction can trap residue if not longitudinal
Mechanical polish, 240 – 320 grit Ra 0.4 – 0.5 µm Pharma, and dairy where the specification is tighter Cost rises steeply; polishing marks still visible
Electropolished Ra 0.3 – 0.5 µm, chromium-enriched surface Pharma, biotech, high-purity Adds lead time; the passive layer is the real benefit, not the roughness
Bright annealed Ra 0.4 – 0.6 µm, no polishing Small bore instrument and sampling lines Cannot be re-polished after bending

Surface roughness alone does not make a line hygienic. A 180 grit bore with a circumferential polish pattern is worse than a coarser longitudinal one, because residue sits in the grooves. Specify the direction as well as the Ra if the line handles viscous product.

Hygienic compliance

Table 4 — The standards behind a “sanitary” claim

Standard Scope What it means for the tube
ASTM A270 Sanitary tube for dairy and food The product specification: grade, dimensions, finish, test
3-A Sanitary Standards US dairy and food equipment design Cleanable, drainable, no crevices; tube is one input to a 3-A certified assembly
FDA 21 CFR 177 Food contact materials 316L with a documented finish meets the intent; the processor holds the compliance record
EHEDG European hygienic equipment design The European equivalent of 3-A; weld quality and surface finish are both assessed
ASME BPE Bioprocessing equipment Stricter than A270 — specifies Ra, weld acceptance and ferrite content for pharma

A270 tube does not by itself make an assembly 3-A or EHEDG compliant. Those certifications apply to equipment, and the tube is one input. Any supplier claiming a tube is “3-A certified” is overstating it — the tube can be supplied to a finish that supports certification.

Which specification your line actually needs

Table 5 — A270 against its neighbours

Specification Written for Choose it when
ASTM A270 Sanitary tube, dairy and food The bore is a product contact surface with a specified finish
ASTM A269 General service austenitic tube Utility, instrument and non-contact lines in the same plant
ASTM A213 Seamless heat exchanger and boiler tube The tube is a pressure part
ASME BPE Bioprocessing equipment Pharma and biotech, where A270 is not detailed enough
ASTM A554 Welded ornamental and mechanical tube Visible frames and guards, not product contact

Inspection

Table 6 — Test scope

Check Status Note
Chemical analysis Required Per heat, on the 3.1 certificate
Tensile test Required Rm, Rp0.2, elongation
Hydrostatic or eddy current Required, either one Eddy current is normal for thin wall sanitary sizes
Flattening test Required Confirms ductility
Surface roughness Required on polished tube Measured on the bore, recorded as Ra
Borescope inspection On request Video record of the bore — the evidence pharma auditors ask for
PMI On request Confirms 316L rather than 304 in a mixed rack

Where A270 tube is used

Dairy process lines

Raw milk, pasteurised product and CIP return. Clamp fittings throughout, so the tube OD tolerance matters as much as the bore finish.

Brewery and beverage

Product transfer, yeast handling and CIP. 316L for the chloride in cleaning chemicals, 180 grit bore as the baseline.

Food processing

Sauces, purees and high-viscosity product, where a circumferential polish pattern would trap residue and the finish must run longitudinally.

Pharmaceutical

Where ASME BPE applies, but A270 with electropolish is often the practical compromise for utility and non-critical process lines.

Cosmetics and personal care

Hygienic transfer of creams and gels. Same finish requirement as food, usually with 316L for the fragrance and preservative chemistry.

Water for injection loops

High-purity distribution, usually BPE grade with electropolish and a documented weld log rather than plain A270.

Frequently asked questions

What makes A270 different from A269?

The surface finish requirement. A269 is a general service tube with no finish control; A270 specifies a sanitary finish on the bore and a tighter dimensional control so hygienic fittings seat. Same alloys, different end use.

What Ra should I specify?

Ra 0.8 µm (about 32 µin) at 180 grit is the dairy and food baseline and is what most specifications quote. Pharma and biotech move to Ra 0.4 µm and electropolish. Below that the cost rises faster than the hygiene benefit.

Do I need 304 or 316L?

316L if there is any chloride in the product or the cleaning chemicals — which covers most CIP regimes. 304 is acceptable for dry product and clean-in-place with chloride-free caustic.

Is the tube 3-A certified?

No — 3-A certifies equipment, not tube. We supply tube to a finish and tolerance that supports a 3-A assembly. Any supplier who claims a 3-A certified tube is overstating what the standard covers.

Can you supply electropolished bore?

Yes, to Ra 0.3–0.5 µm, with the chromium-enriched surface that comes with it. Electropolish adds about a week to the lead time and is usually specified for pharma rather than food.

What is the wall tolerance?

12.5% of nominal, which is the A270 figure. If a drawing asks for ±10% it is either quoting a different specification or asking for something the standard does not require — worth clarifying before ordering.

How do you protect the finish in transit?

Plastic caps on both ends, tubes bundled in plastic sleeve, and no strapping in contact with the polished bore. A polished tube that arrives with strap marks is scrap.

What is the minimum order and lead time?

300 kg per size. Lead time is 25–30 days; electropolished and borescope-inspected material runs about a week longer.

Send the finish, not just the grade. OD, wall, grade, grit or Ra, and whether the bore is product contact — that is enough for a firm price. If the finish you have specified is not achievable on that size, we will say so before quoting.
Request a quote
WhatsApp

Related products

All stainless steel tube — austenitic, martensitic and duplex · Guide: NACE MR0175 sour service requirements

Request a quotation

Tell us OD, wall, grade, finish (grit or Ra) and whether the bore is a product contact surface. We reply within 24 hours with price, lead time and the inspection scope.

    Your Name *

    Your Email *

    Company Name

    Phone / WhatsApp *

    Grade & Standard (e.g. ASTM A106 Gr.B, EN 10216-2 P265GH)

    Size, OD × WT (e.g. 88.9 × 5.49 mm)

    Quantity & Unit (e.g. 500 m / 20 t)

    Destination Port

    Drawing or Datasheet (pdf, dwg, step, xlsx; max 5 MB)

    Further Information